UPVC Replacement Door Handles
The handles on your doors get worn out over time and need to be replaced. In this case, it is crucial that the new handles are in line with the dimensions of the previous handle.
The top screw position as well as the lever and keyhole dimensions are the three measurements that you need to verify. Use the size guide to aid you.
Inline Lever/Lever
A lever/lever handle is a contemporary door handle designed to suit new or replacement doors. This kind of handle is available in various designs and finishes. This handle is available from several manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.
Fab and Fix Windsor Inline Sprung Lever Door Handle
The uPVC/Composite door handles are made of sturdy materials and are suitable for multi-point lock doors which require a robust design. The handles are inline and operate off the same spindle and screw fixings, so they can be easily incorporated into new or existing uPVC/Composite doors.
The handle can be adjusted and angled to fit any user. The handle has been endurance tested to 200,000 cycles. This helps to ensure the quality of the finish and performance of the handle over time. The sprung lever can be cut to fit the widest range of locks. This is especially useful in doors with smaller door frames where the cylinder is further back. A shorter lever is an excellent option for doors that have latches that can be activated by the thumb turn inside.
Lever Pad
A Lever Pad door handle made of upvc functions differently to the lever type handles that are found on the majority of doors. The handle can use a single spindle (inline) or independently from both sides using two inline or offset spindles (pad). They are generally employed on UPVC double glazed doors. They come in a variety of styles and finishes.
The handles are available in various finishes, including White Chrome and Gold. The finish is in line with BS EN 1670:2007 Grade 5 and is also resistant to corrosion, which gives the handle a high degree of durability and performance for the intended use.
All UPVC levers for handles come with a spindle, screws and can be mounted on a uPVC door. The backplate fixing centres of 211mm allow for a wider size of handle which is often a benefit when replacing a damaged or worn multi-point door lock mechanism. These handle levers are also spring-loaded, which solves the issue of handles hanging out of the horizontal position when they are not being used.
When choosing a replacement UPVC handle and spindle, it is crucial to match the PZ dimensions of the multipoint lock as well as the uPVC door. This measurement can also be called 'handle centres or cylinder centres'. It is important to match the correct handles.
When you have the right PZ size you will then need to ensure that the lever pads and push pads are a suitable shape for the American with Disabilities Act (ADA) approved handles you need for your doors. They are typically square or round with an internal lever, and an external push pad.
The majority of UPVC Lever Pads we offer are spring-loaded. This means they return to a horizontal position when they are not in use instead of hanging, and possibly securing to the frame. This prevents draughts from entering the home. It is also the case that the majority of the UPVC lever pad handles are handed that allows you to put them on either side of the door.
Euro Cylinder
Cylinder locks are commonly found on uPVC doors, but can also be found on other types of doors. The cylinder lock is operated by using a key that unlocks the cylinder's case. This exposes pins that can be aligned with those inside the lock, allowing them to turn the camera that rotates, opening the door. Euro Cylinders are available with up to six pins. Doors that are internal and external require different levels of security.
The selection of a cylinder is crucial. It is based on the amount of use your doors and handles receive. upvc door handle www.repairmywindowsanddoors.co.uk , for example should be equipped with higher security cylinders and internal doors can be secured with an ordinary cylinder. Some cylinders have extra features that increase security, such as anti-drill or anti bump properties.
A euro cylinder should be properly measured to ensure it is the right size for your door. The cylinder must be measured from the central screw hole to the ends of the cylinder. This includes the thumb turn if there is one. If you cannot measure using the lock in a fixed position, you can remove it. A cylinder that is protruding beyond the handle and escutcheon may be vulnerable to attacks, such as lock snapping, so it is essential to make sure it's not too long.
The design of most newer cylinders comes with anti-drilling as well as bump resistance features. These features are designed to minimize the chances of an attack by forcing the cylinder to rotate in the opposite direction. This will help to deflect attacks and protect your door.
There are cylinders that have been designed to resist snapping. This is a growing kind of attack on cylinders, where the break line in the lock is attacked using a special tool to break the front of the cylinder to allow the door to open. This is a faster and easier way to gain access than a multipoint locking system. It also leaves less evidence of the break-in which could hinder insurance claims.
Spring Cassette
This spring cassette is found inside the base plate of your door handle. It is a spring-loaded solution to bring your multipoint lock handles to their resting position after use. Previously a lot of handles of this kind didn't have a spring built into them, and as a result, they tend to droop or drop once the locking mechanism is removed. Adding this simple component is among the best methods to correct this issue and is an effective way to keep your upvc doors from getting stuck in the open or closed position, as these aren't always simple to manually close by hand.
These spring cassettes were designed to be used with a spring multipoint locks. They will not fit handles that are not sprung and you'll have to cut a hole into your backplate in order for them to fit. (Please check the image for a detailed diagram). These cassettes can be used as a replacement to damaged or missing cassettes in the backplate of uPVC door handles. They are sold as one unit. They feature a square cut out that can accommodate an 8mm shaft.
These spring cassettes offer an excellent value solution for the issue of sagging door handles. They are simple to install and will prolong the life span of your uPVC doors. For more information about our range of uPVC accessories and spares, you can get in touch with our team. We are always happy to provide expert advice and support you.